AL Compact 5/8kV NLEPR Insulation 133/100% IL PVC Jacket. MV 105 - Tray Rated - Sunlight Resistant - For Direct Burial
Type MV-105 Three Conductor Aluminum, 115 Mils No Lead Ethylene Propylene Rubber (NL-EPR) 133% Insulation Level, Tape Shield, Polyvinyl Chloride (PVC) Jacket, Dual Rated UL/CSA. Silicone Free
Application & Features
Southwire’s 5KV cables are suited for use in wet and dry areas, conduits, ducts, troughs, trays, direct burial, and where superior electrical properties are desired. These cables are capable of operating continuously at the conductor temperature not in excess of 105°C for normal operation, 140°C for emergency overload, and 250°C for short circuit conditions. Rated at -35°C for cold bend when UL listed. Rated at -40°C for cold bend and cold impact and marked with "LTGG" when CSA listed or dual UL/CSA listed. For uses in Class I and II, Division 2 hazardous locations per NEC Article 501 and 502.Rated for 1000 lbs./FT maximum sidewall pressure.
Specifications
| Cond. Size | Cond. Strands | Diameter Over Conductor (in) (cm) | Diameter Over Insulation (in) (cm) | Inner Layer Thickness (mils) (mm) | Diameter Over Shield (in) (cm) | Ground Size | Outer Layer Thickness (mils) (mm) | Approx. OD (in) (cm) | Approx. Weight (lbs/1000') (kgs/km) | Max Pull Tension (lbs) (kg) | Min. Bend Radius (in) (cm) | |
| More Options |
2 AWG
2 AWG
|
7
7
|
0.268
0.68
|
0.536
1.36
|
115
2.92
|
0.596
1.51
|
1x4
1x4
|
80
2.03
|
1.499
3.81
|
1123
1671
|
1194
541.59
|
10.4
26.42
|
| More Options |
3/0 AWG
3/0 AWG
|
18
18
|
0.422
1.07
|
0.691
1.76
|
115
2.92
|
0.751
1.91
|
1x4
1x4
|
110
2.79
|
1.894
4.81
|
1783
2653
|
3020
1369.85
|
13.2
33.53
|
| More Options |
4/0 AWG
4/0 AWG
|
19
19
|
0.474
1.20
|
0.743
1.89
|
115
2.92
|
0.803
2.04
|
1x4
1x4
|
110
2.79
|
2.006
5.10
|
2069
3079
|
3808
1727.28
|
14.0
35.56
|
| More Options |
350 KCMIL
350 KCMIL
|
35
35
|
0.615
1.56
|
0.892
2.27
|
115
2.92
|
0.952
2.42
|
1x3
1x3
|
110
2.79
|
2.334
5.93
|
2808
4179
|
6300
2857.63
|
16.3
41.40
|
* Strand count meets minimum number per ASTM
| Cond. Size | DC Resistance at 25C (ohms/1000') (ohms/km) | AC Resistance at 75C (ohms/1000') (ohms/km) | Capacitive Reactance (ohms/1000') (ohms/km) | Inductive Reactance (ohms/1000') (ohms/km) | Zero Sequence Impedance (ohms/1000') (ohms/1000') | Positive Sequence Impedance (ohms/1000') (ohms/1000') | Shield Short Circuit Current 6 Cycles | Allowable Ampacity In Duct 90C | Allowable Ampacity In Duct 105C | Allowable Ampacity In Air 90C | Allowable Ampacity In Air 105C | |
| More Options |
2 AWG
2 AWG
|
0.267
0.40
|
0.336
0.50
|
0.036
0.05
|
0.041
0.06
|
0.705 + j0.524
0.705 + j0.524
|
0.336 + j0.041
0.336 + j0.041
|
1877
1877
|
105
105
|
110
110
|
110
110
|
120
120
|
| More Options |
3/0 AWG
3/0 AWG
|
0.105
0.16
|
0.133
0.20
|
0.025
0.04
|
0.035
0.05
|
0.509 + j0.438
0.509 + j0.438
|
0.133 + j0.034
0.133 + j0.034
|
2354
2354
|
180
180
|
195
195
|
195
195
|
215
215
|
| More Options |
4/0 AWG
4/0 AWG
|
0.084
0.13
|
0.105
0.16
|
0.023
0.03
|
0.034
0.05
|
0.48 + j0.414
0.48 + j0.414
|
0.105 + j0.033
0.105 + j0.033
|
2515
2515
|
205
205
|
220
220
|
225
225
|
250
250
|
| More Options |
350 KCMIL
350 KCMIL
|
0.050
0.07
|
0.065
0.10
|
0.019
0.03
|
0.032
0.05
|
0.434 + j0.353
0.434 + j0.353
|
0.065 + j0.031
0.065 + j0.031
|
2977
2977
|
280
280
|
310
310
|
310
310
|
345
345
|
* NEC ampacities are based on:
* For Duct: Table 310.60(C)(14) Detail 1.
* For Free Air: Table 310.60(C)(6).
* Inductive impedance is based on non-ferrous conduit with one diameter spacing center-to-center.
* Sequence Impedance values are based on Rho Earth Resistivity: 100 Ohm-Meter/1000ft.
* Capacitive Reactance is between Phase-to-Shield.
Standards & References
- ASTM B801 Concentric-Lay-Stranded Conductors of 8000 Series Aluminum Alloy
- ASTM B836 Compact Rounded Stranded Aluminum Conductors
- UL 1072 Medium-Voltage Power Cables
- UL 1685 Vertical-Tray Fire Propagation and Smoke Release Test
- UL 2225 Cables and Cable-Fittings For Use In Hazardous (Classified) Locations
- CSA C22.2 No.230 Tray Cables - Rated TC-ER
- CSA C22.2 No. 2556 / UL 2556 Cable Test Methods
- CSA C68.10 Shielded Power Cables for Commercial and Industrial Applications - 5 to 46 KV
- ICEA S-93-639 (NEMA WC 74) 5-46 KV Shielded Power Cable
- ICEA S-97-682 Standard for Shielded Utility Cable Rated for 5 - 46kV
- AEIC CS-8 Specification for extruded dielectric shielded power cables rated for 5 through 46KV (Qualification Test Requirements)
- Made in America: Compliant with both Buy American and Buy America Act (BAA) requirements per 49 U.S.C. § 5323(j) and the Federal Transit Administration Buy America requirements per 49 C.F.R. part 661
Construction
- Conductor: Class B compact stranded 8000 Series aluminum per ASTM B800 and ASTM B836
- Conductor Shield: Semi-conducting cross-linked copolymer; A conductor separator is used for cable size larger than or equal to 500 Kcmil
- Insulation: 115 Mils No Lead Ethylene Propylene Rubber (NL-EPR) 133% Insulation Level,
- Insulation Shield: Strippable semi-conducting cross-linked copolymer
- Copper Tape Shield: Helically wrapped 5 mil copper tape with 25% overlap
- Grounding Conductor: Class B compressed stranded bare copper ground per ASTM B3 and ASTM B8
- Filler: Wax paper filler
- Binder: Poly glass tape
- Overall Jacket: Polyvinyl Chloride (PVC)