CU PE/PVC SHIELDED CONTROL CABLE
Control Cable 600 Volt Copper Conductors, Polyethylene Polyvinyl Chloride (PE/PVC) Insulation Shielded Polyvinyl Chloride (PVC) Jacket, Control Cable Conductor Identification Method 1 Table 1. Silicone Free
Application & Features
Southwire’s 600 Volt control cables are suited for use in wet and dry areas, conduits, ducts, troughs, trays, direct burial, aerial supported by a messenger, and where superior electrical properties are desired. These cables are capable of operating continuously at the conductor temperature not in excess of 90°C for normal operation in wet and dry locations, 130°C for emergency overload, and 250°C for short circuit conditions. Only UL rated constructions with 3 or more conductors are listed for exposed runs (TC-ER) per NEC 336.10.
Specifications
Select a set of products below for more information:
| Conductor | ||||||
| No. of Conductors | Size (AWG or kcmil) (mm2) | No. of Strands | Insulation Thickness (mils) (mm) | Nom. OD (mils) (mm) | Nominal Total Weight (lbs/1000') (kgs/km) | |
| More Options |
12
12
|
14 AWG
14 AWG
|
7
7
|
20
0.51
|
706
17.95
|
340
506
|
| More Options |
2
2
|
10 AWG
10 AWG
|
7
7
|
20
0.51
|
472
12.00
|
159
236
|
| More Options |
3
3
|
10 AWG
10 AWG
|
7
7
|
20
0.51
|
500
12.72
|
201
299
|
| More Options |
5
5
|
10 AWG
10 AWG
|
7
7
|
20
0.51
|
628
15.96
|
309
460
|
| More Options |
7
7
|
10 AWG
10 AWG
|
7
7
|
20
0.51
|
661
16.79
|
388
578
|
| More Options |
8
8
|
10 AWG
10 AWG
|
7
7
|
20
0.51
|
796
20.23
|
495
736
|
| More Options |
9
9
|
10 AWG
10 AWG
|
7
7
|
20
0.51
|
789
20.05
|
497
740
|
| More Options |
12
12
|
10 AWG
10 AWG
|
7
7
|
20
0.51
|
928
23.59
|
675
1004
|
Standards & References
- ASTM B3 Standard Specification for Soft or Annealed Copper Wire
- ASTM B8 Concentric-Lay-Stranded Copper Conductors
- ICEA S-58-679 Control Cable Conductor Identification Method 1 Table 2
- ICEA S-73-532 Standard for Control, Thermocouple Extension and Instrumentation Cables
- ICEA S-95-658 (NEMA WC70) Power Cables Rated 2000 Volts or Less for the Distribution of Electrical Energy
- IEEE 1202 FT4 Vertical Tray Flame Test (70,000 Btu/hr) and ICEA T-29-520 - (210,000 Btu/hr)
- VW-1 (Vertical-Wire) Flame Test
Construction
- Conductor:7 strands class B compressed bare copper per ASTM B3 and ASTM B8
- Insulation:Polyethylene (PE) 20 Mils thick and Polyvinyl Chloride (PVC) 10 Mils thick for all cable sizes
- Filler:Polypropylene filler on cables with 5 or less conductors
- Binder:Polyester flat thread binder tape applied for cables with more than 5 conductors
- Shielding:5 mils tape shield
- Rip Chord:Rip chord for ease of jacket removal
- Overall Jacket:Polyvinyl Chloride (PVC) Jacket
- Color codes available upon request
Resources
There are no downloadable resources for this product.